| 2 | Normative References | Access to copies of listed standards |
| 4 | General requirement | None |
| 5 | General conditions for the tests | None |
| 6 | Classification | None |
| 7 | Marking and instructions | Spirit, Water |
| 8 | Protection against access to live parts | Test probe B, 13 and 41 of IEC61032, voltmeter mill ammeter, force gauges, 2000ohm non-inductive resister |
| 9 | Starting of motor-operated appliances | None |
| 10 | Power input and current | Voltmeter, ammeter, wattmeter |
| 11 | Heating | Temperature controlled room,Temperature Recorder, fine wire thermocouples, test corners,Winding resistance measurement system, Loading as required by part 2's |
| 12 | Void | |
| 13 | Leakage current and electric strength at operating temperature | Leakage current meter, isolation transformer, HV test supply, Network(Fig.4 of IEC60990) |
| 14 | Transient overvoltage | Inpulse voltage test generator and monitor |
| 15 | Moisture resistance | Oscillating hoop IP test equipment, measurement beaker, spray nozzle |
| 16 | Leakage current and electric strength | Environmental chamber capable of 93%RH at selected temp. with HV test facilities |
| 17 | Overload protection of transformers and associated circuits | Included above |
| 18 | Endurance | As required by part 2's |
| 19 | Abnormal operation | As above with suitable protection against damage to equipment, personnel and property in event of abnormal failureElectrostatic discharge test apparatus (IEC 61000-4-2), Radiated field test apparatus (IEC 61000-4-3), Fast transient burst test apparatus (IEC 61000-4-4), Voltage surge test apparatus (IEC 61000-4-5), Injected current test apparatus (IEC 61000-4-6), Voltage dip and interruption test apparatus (IEC 61000-4-11), Mains signal test apparatus (IEC 61000-4-13) |
| 20 | Stability and mechanical hazards | Inclined plains, masses, force gauges |
| 21 | Mechanical strength | Impact hammer, Hardened steel pin, Force gauges |
| 22 | Construction | Test rig for torque on pin supported appliance, Heating cabinet(70 ±2℃)
Test probe 11 of IEC61032,
Test fingernail
Force gauge, Test finger nail
Oxygen bomb
Methylated spirits and Pressure apparatus
Water pressure test apparatus |
| 23 | Internal wiring | Flexing test apparatus |
| 24 | Components | Laboratory may or may not have facilities for testing to component standards.
Certification by specialist laboratories is accepted for compliance |
| 25 | Supply connection and external flexible cords | Flexing test apparatus, Cord anchorage force & torque tester |
| 26 | Terminals for external conductors | Torque screwdriver |
| 27 | Provision for earthing | Earth continuity tester, access to ISO2178 and 1463 testing |
| 28 | Screws and connections | Torque gauge |
| 29 | Creepage distances, clearances and distance through insulation | Mechanical measurement tools, Rod and ball gauges
Proof tracking test apparatus |
| 30 | Resistance to heat and fire | Ball Pressure test apparatus, Glow wire & Needle flame test apparatus,
Apparatus for low power circuit determination.
Horizontal and vertical burning test apparatus |
| 31 | Resistance to rusting | Part2 requirements |
| 32 | Radiation, toxicity and similar hazards | Part2 requirements |
| Annex A | Routine tests | None |
| Annex B | Appliances Powered by rechargeable batteries | Free fall test apparatus (IEC60068-2-32) |
| Annex C | Ageing Test on Motors | Nothing special |
| Annex D | Alternative requirements for protected motors | Nothing special |
| Annex E | Needle flame test | Needle flame test apparatus (IEC 60695-2-2) |
| Annex F | Capacitors | Impulse voltage test apparatus, Endurance test apparatus (IEC 60384-14) |
| Annex G | Safety isolating transformers Circuit for measuring leakage current | Nothing special |
| Annex H | Switches | Endurance test apparatus (61058-1) |
| Annex I | Motors having basic insulation that is inadequate for the rated voltage of the appliances | Nothing special |
| Annex J | Coated printed circuit boards | Coated printed circuit boards test apparatus (IEC60664-3) |
| Annex K | Overvoltage categories | None |
| Annex L | Guidance for the measurement of clearances and creepage distances | None |
| Annex M | Pollution degree | None |
| Annex N | Proof tracking test | Proof tracking test apparatus (IEC 60112) |
| Annex O | Selection and sequence of the test of clause 30 | None |
| Annex P | Guidance for the application of this standard to appliances used in warm damp equable climates | None |
| Annex Q | Sequence of tests for the evaluation of electronic circuits | None |
| Annex R | Software evaluation | Capability for Soft ware evaluation (IEC 60730-1) |
